Servicing industry specific calibration and testing equipment.
AIM Calibrations provides top quality servicing and calibration of technical equipment, electrical and plumbing instruments for your business.
WHAT WE DO
Servicing and calibration to suit your business needs.
We sell, service, calibrate and repair a wide range of equipment such as:
- Autoclaves
- Panflushers
- Washer Disinfectors
- Weigh Chairs & lifting units.
We also calibrate:
- Cool rooms
- Medical Fridges
- Backflows
- Thermometers
- Gas Detection Units
- Multi-meters
- Clamp Meters
- Appliance Testers
- Torque Wrenches
- Pressure Gauges and much more.
![Close up sterilized packaged dentist instruments. Sterility and safety care concept. Selective focus, space for text.](http://aimcalibrations.com.au/wp-content/uploads/2020/05/close-up-sterilized-packaged-medical-instruments.jpg)
![medical vital signs monitor in a hospital](http://aimcalibrations.com.au/wp-content/uploads/2020/05/medical-vital-signs-monitor-in-a-hospital.jpg)
INDUSTRIES WE SUPPORT
MEDICAL
VETERINARY
NURSING HOMES
DENTAL
PODIATRY
TATTOO / BEAUTY
ELECTRICAL
PLUMBING
GAS DETECTORS
OUR AUTOCLAVE SERVICES
General Service
A general service is required to be carried out 12 months by trained technicians, but is recommended to be carried out every 6 months for heavily used units in larger surgeries with high turnover . It involves checking and replacing the door seal if required, then running a full sterilizing and drying cycle with a bacterial indicator vial and monitoring pressure and temperature to ensure correct sterilization is being achieved.
![Vertical laboratory autoclaves for sterilizing samples](http://aimcalibrations.com.au/wp-content/uploads/2020/05/vertical-laboratory-autoclaves-for-sterilizing-samples.jpg)
"Time at Temperature" or Heat Penetration Study
A ‘Time At Temperature’ test or ‘Heat Penetration’ study is required by Australian Standards 4187 and 4815 to be carried out by trained technicians on units once every 12 months. This is performed by carrying out temperature monitoring of your hardest to sterilize pack in your largest or most difficult to sterilize load. We will then recommend sterilizing times to ensure that the minimum sterilizing requirements are being met with an additional safety margin.
![](http://aimcalibrations.com.au/wp-content/uploads/2020/05/dental-autoclave-with-dentistry-tools-in-a-clinic.jpg)
Process Validation
A process validation is required by Australian Standards 4187 and 4815 to be carried out on units once every 12 months. This can be performed by our technicians, and involves running three consecutive cycles with two bacterial indicator vials per cycle (one in the cold spot and one in the ‘challenge’ pack) to ensure that proper sterilization is being achieved on a consistent basis. The vials are then incubated to monitor consistent sterilization function.
![Steam Sterilization Biological Indicator](http://aimcalibrations.com.au/wp-content/uploads/2020/05/steam-sterilization-biological-indicator.jpg)
Expertise
The majority of services can be carried out on site and we have a fully equipped workshop to handle any larger repairs or upgrades. And with over 20 years experience in medical equipment field and we are fully stocked with spare parts and loan units to handle any issues you may have. We are contactable 24/7 hours a day for any technical advice or queries you may have on the operation of your unit.
Loan Units
Our stock of loan units are available if your sterilizer is out of action to ensure that you have no interruption to your sterilizing capabilities. These are available for delivery by our technicians as we assess and repair your unit.
![medical vital signs monitor in a hospital](http://aimcalibrations.com.au/wp-content/uploads/2020/05/medical-vital-signs-monitor-in-a-hospital.jpg)